|
|
|
|
|
Fresh on the heels of the last update I'm finally moving forward with the restoration of this 1971 Corvette - literally.
With the rear clip repairs now officially complete my attention has been directed to the front clip area of the car. Quite
some time ago I spent a fair bit of time repairing, rehabilitating and painting the firewall. Since that time it's been
sitting in the garage, safely tucked away, waiting to be installed back on the car.
Finally the time to reinstall the firewall has arrived!
But, before the firewall could be installed, I had to remove the body from the chassis to allow
better
access to the floor pan area. So, using the
Corvette body lifting rack I developed
and built, the body was lifted and the chassis was
rolled out from underneath.
Once the chassis was rolled out of the way the body was lowered onto a set of sawhorses
which worked great as they they placed the firewall
at an excellent working height.
With the body safely settled on the sawhorses I did a quick dry fit of the firewall to see how things fit together. I did find that, after being left
unsupported for so long, the transmission tunnel of the floor pan had sagged an
inch or so. In order to get the firewall to fit
in place a tie-down was connected between the t-top cross bar and the bracket on the transmission tunnel.
Once connected the tie-down was cinched tight to pull the transmission tunnel
back up to where it was supposed to be. Once the tunnel was pulled into place the firewall slipped into place quite easily.
Keep in mind that the flange of the firewall mounts to the underside of the
floor pan. This seems a bit counterintuitive at first, but it makes quite a bit
of sense once you think about it. This arrangement orientates the lap between
the two panels such that water from the firewall can simply roll off onto the
floor pan with little opportunity to get through the body seam and into the
passenger compartment.
Aligning the firewall turned out to be pretty simple.
Along the top of the firewall there's a line of rivet holes which I simply aligned with the corresponding holes in the
bird cage/lower windshield cross bar. Once the holes were aligned a few pop-rivets
were temporarily placed in the holes to keep things aligned (I didn't actually
'pop' them for now). Several clamps were also used to secure the firewall the
overall alignment and fit was reviewed. In the end I found the fit to be pretty
tight - there
wasn't a lot of opportunity for adjustment which made things easy. The
left/right and up/down alignment was based on the rivet holes along the bird
cage and the front to back fit was quite easy to figure out - the firewall is in
the right spot when it bottoms
against the door pillar!
However, I did check a few other areas just in case (better safe than sorry). In
particular, the right to left
fit of the firewall was verified by comparing how much of the door skin projected past the mounting flanges on the firewall.
My check found that approximately 1/8" of the thickness of the door skin
projected beyond the surface of the mounting flange on both sides. With the
alignment matching on both sides I moved forward with preparing the firewall for
final installation.
First, I prepped for the connection between the floor pan and the lower portion
of the firewall. This was an area that I certainly couldn't clamp and, because
the two surfaces were not tight together, some form of temporary attachment was
required. After giving it some consideration I decided to use temporary screws
much like I used on the rear quarter panel (see this
update for more information on how to use temporary screws to attach two
fiberglass panels together). Once it was all said and done approximately 10 to
12 screws had been installed.So, with the proper fit of the firewall established,
and holes for the temporary screws drilled, the firewall was removed so it could
be prepped for installation. Prepping primarily involved
scuffing all of the mating surfaces with 80 grit sandpaper and then thoroughly cleaning them with
lacquer thinner. Although it didn't take a tremendous amount of time, this became
a pretty tedious process. There were a lot of bonding surfaces to address and
the PPG DP40 epoxy primer I used made for tough sanding.
Once all of the bonding surfaces were prepped the application of the sealant and bonding adhesive got underway. At this point
I found it very helpful to be well organized. You'll want all of your tools set aside and ready for use, plenty of adhesive, and an extra helper if possible.
Even with materials that allow for longer working times, you don't want to be
searching for a putty knife or your rivet gun while your adhesive is curing. You
only have one shot at this so it's best to spend an extra bit of time to get
properly setup and prepared. That said, you
could probably complete the firewall installation with just one person. However, having
an extra set of hands to help place, align and seat the firewall in the adhesive makes the
process
a lot easier.
For adhesives I decided to use a combination of products instead of just the Lord Fusor 127EZ
epoxy that was used on the rear clip body panels. Given
how much surface area needed to be coated, and the high price of the 127EZ, a
combination of materials seemed to make good sense. After all, I wanted to set
the firewall in a good bed of adhesive to keep things watertight, but it all
didn't need to be high end epoxy adhesive.
To start, a thick bead of high quality flexible polyurethane construction adhesive was applied along the outside
edges of the mating surfaces. The primary purpose of this product was to ensure a flexible and watertight seal.
Next I applied a good thick bead of Lord Fusor 127EZ along the inner edges of the bonding surfaces. Both products were
purposefully
selected to provide a 60 minute working time. Mounting the firewall definitely didn't take 60 minutes, but it was really nice to have
plenty of time to set the firewall without feeling hurried.
Once the adhesive was applied to the birdcage a thick bead was also applied to the bottom bonding surface of the firewall. The adhesive
could have been applied to the underside of the floor pan, but I felt applying it to the firewall would be easier.
So, with the sealant and adhesive in place the firewall was carefully lifted and slid into place. The biggest effort was to slide the firewall
into place while trying to avoid scraping all of the adhesive off the firewall to floor pan mounting flanges. To help
provide a bit more clearance I tightened
up on the strap between the t-top cross bar and transmission tunnel. Although this caused a bit of pinching along the sides of the transmission
tunnel, it helped overall. Once the firewall was firmly in place the strap was released
and the transmission tunnel deflected down
into place.
Next, and working quickly, new 3/16" diameter pop rivets were installed to permanently affix the firewall to the bird cage. This is where it came in really
helpful to have an extra set of hands. These rivets take a reasonable amount effort to install and, after
completing a half dozen or
so, your hand can start getting pretty fatigued. My friend and I took turns
installing the rivets which helped make quick work of the task. Once the rivets
were installed the screws between the floor pan and firewall were installed and
tightened to keep the two panels in tight
contact while the adhesive cured.
After installing all the rivets and screws there were quite a few areas where adhesive had oozed out
from the bonding seams. To avoid having a big mess
to clean up later a putty knife was used to scrape away the excess material before
the adhesive fully hardened.
The end result was a very neat and professional looking job. Overall I was quite pleased with the results and, at this point,
decided to take the rest of the night off while the adhesive cured.
Here's a view of the firewall from inside the passenger compartment. If you look closely you can see the heads of the screws used to temporarily
attach the floorpan to the firewall.
A view from beneath the firewall. Once again, if you look carefully, you can see the shanks of the screws used to temporarily hold the
firewall and floorpan together.
The next day my friend stopped by once again to help drop the body back onto the chassis. However, before doing so, the engine was pulled
one last time. Installation of the front clip is next on my to-do list and the engine and transmission would just be in the way.
Although it was a bit of a hassle, I knew that removing the engine and
transmission would make things a lot easier down the road.
And here it is - the firewall mounted back to the birdcage and installed on the chassis. It's remarkable how quickly the car
has started coming together over the past few months. Next up - front clip!!!!
That's it for this update. As noted above, installation of a new one-piece replacement front clip is next on the to-do list.
I learned a tremendous amount while installing the new clip so I'll try and
convey as much of that information as I can.
Stay tuned for a new update in a month or two. In the meantime please feel
free to stop by the
Corvette
Restoration Forum to share your project with others, or to simply see what's
going on. Lastly, if you haven't done so already, please
Like this project on
Facebook to receive the latest news regarding project developments, updates,
and progress!
|
|
